PRODUCT DISCRIPTION:
| Surfaces | GRP, laminates, steel, aluminum | |
| Area | Above and below waterline | |
| Function | Grounding Intercoating Filling Antiosmotic Anticorosive | |
| Application | spray can | |
| Theoretical coverage for 400 ml | 1-2 м2 | |
| Number of coats | 2 – 4 | |
| Pot life 20°C | 48 h | |
| Time between layers without sanding | 5~10 minutes | |
| Color (matt) | white | |
| Pack | 400 ml | |
| Code | 38758 | |
Before triggering, shake can thoroughly for 2 minutes after agitation balls are heard.
Remove the red pushbutton from the cap.
Turn the can by 180° and fit the pushbutton onto the pin in the base of the can.
Turn the can upside down and place on a firm surface.
Press the red pushbutton all the way in with the palm of your hand.
After triggering, shake can again thoroughly for 2 minutes after agitation balls are heard.
Set the adjustable spray nozzle to the size of the damage and damage pattern.
Spray distance: 10 ~ 20cm.
Standard application: approx. 2÷4 spray coats, recommended dry film layer: 80 ~200 μm
NOTICE: For antiosmosis and anticorrosion protection recommended DTF is 240 μm.
Allow a flash-off time of approx. 5-10 minutes between spray coats.
After painting, turn the can upside down and spray the valve until empty.
The completely empty spray cans can be disposed of in the recycling waste container.
Cans with hardened material must be disposed of as special waste.
CINTA DE BARNIZAR CINTA DE BARNIZAR IMPERMEABLE MASTER CINTA UNIVERSAL – PLATA CINTA DE BARNIZAR La cinta de barnizar de […]
Mascara para polvo Guantes de nitrilo MASTER Guantes de nitrilo desechables Mono de trabajo desechable Mono de trabajo de poliéster […]
Recomendado para disengrasar la superficie antes de pintar Envase de concentrado : 1 l / código: 3990 INFORMACIONES TÉCNICAS: TDS […]
IMPRIMACIÓN EPOXI Antiosmósis HS Sea-Line® 3 : 2 Imprimación epoxi de 2 componentes, de alta calidad, alto espesor. No contiene […]
IMPRIMACIÓN EPOXI anticorrosiva Sea-Line® 4 : 1 Imprimación epoxi anticorrosiva de 2 componentes, de alta calidad. Especialmente recomendado para la […]
Disolvente los trabajos es muy importante utilizar el disolvante adecuado lo que proporciona los parámetros apropiados de la pintura – […]
No, polyurethane is a 2-component paint (base + hardener) and after applying 2-component paint to 1-component paint, the proper adhesion of the paint to the surface will not be maintained, the paint will begin to wrinkle and surface defects will appear.
If the scratches are not deep, then we can renew the scratched side by polishing with Sea-Line polishing pastes. Above the waterline, when the scratches are not deep, the surface can be repaired with a DRY FAST gel coat filler. Deep scratches should be filled with epoxy filler (selected depending on the requirements of the scratched surface), painted with a primer and then painted with topcoat.
Para rellenar cavidades y hacer frente a las desigualdades causadas por daños o durante el curso de la producción
Barcos de superficie de impacto de las actividades de ósmosis y la corrosión destructiva en ambientes hostiles
Protección contra el agua y contra los efectos negativos de los rayos UV
Proteger la parte inferior de la embarcación antes de las incrustaciones de algas y conchas. Protección contra el agua
Eliminación efectiva de arañazos, color refrescante y gelcoat brillo o pintura
Preparaciones especializados para la limpieza y restauración efectiva
Laminación, encolado y relleno de fisuras en gelcoat
Una serie de productos útiles durante el constructor de barcos de trabajo
