Lengua:

MULTIFUNCTIONAL 2K SPRAY EPOXY PRIMER

Página web » Productos » Imprimaciones » MULTIFUNCTIONAL 2K SPRAY EPOXY PRIMER
Zabezpieczenie łodzi
MULTIFUNCTIONAL 2K SPRAY EPOXY PRIMER

EPOXY PRIMER MULTIFUNCTIONAL 2K SPRAY

PRODUCT DISCRIPTION:



BASIC INFORMATION:

SurfacesGRP, laminates, steel, aluminum
AreaAbove and below waterline
FunctionGrounding
Intercoating
Filling
Antiosmotic
Anticorosive
Applicationspray can
Theoretical coverage for 400 ml 1-2 м2
Number of coats2 – 4
Pot life 20°C48 h
Time between layers without sanding5~10 minutes
Color (matt)white
Pack400 ml
Code 38758

APPLICATION INSTRUCTION:

potrzasnij

Before triggering, shake can thoroughly for 2 minutes after agitation balls are heard.

spray 2K - korek

Remove the red pushbutton from the cap.
Turn the can by 180° and fit the pushbutton onto the pin in the base of the can.

spray 2K - wcisnij korek

Turn the can upside down and place on a firm surface.
Press the red pushbutton all the way in with the palm of your hand.

potrzasnijAfter triggering, shake can again thoroughly for 2 minutes after agitation balls are heard.

spray 2K - ustaw dysze

Set the adjustable spray nozzle to the size of the damage and damage pattern.

spray 2K - aplikacja

Spray distance: 10 ~ 20cm.

spray 2K - ilosc warstw

Standard application: approx. 2÷4 spray coats, recommended dry film layer: 80 ~200 μm
NOTICE: For antiosmosis and anticorrosion protection recommended DTF is 240 μm.

spray 2K - czas

Allow a flash-off time of approx. 5-10 minutes between spray coats.

spray 2K - oczysc

After painting, turn the can upside down and spray the valve until empty.

spray 2K - utylizacja

The completely empty spray cans can be disposed of in the recycling waste container.
Cans with hardened material must be disposed of as special waste.

TECHNICAL INFORMATION:


Compartir:

¿Tienes alguna pregunta?
Le responderemos lo antes posible

Productos relacionados

de MULTIFUNCTIONAL 2K SPRAY EPOXY PRIMER


Ver también
Otros productos de esta categoría

Nuestras FAQ
Respuestas a las preguntas más frecuentes

Do you have to paint the scratched side of the boat?

If the scratches are not deep, then we can renew the scratched side by polishing with Sea-Line polishing pastes. Above the waterline, when the scratches are not deep, the surface can be repaired with a DRY FAST gel coat filler. Deep scratches should be filled with epoxy filler (selected depending on the requirements of the scratched surface), painted with a primer and then painted with topcoat.

Why the resin does not harden?

Possible causes

  • Too low temperature of ambitne,
  • Incorrect proportion of base and herdener,
  • Mixing two components from two different manufacturers

How to prevent

  • Apply the correct proportions of components
  • Maintain steady temperature (around 20ﹾC) during whole hardening process,
  • Mix the products thoroughly and bleed the mixture.

How to remove

  • The uncured mass requires complete removal from the surface.

Why despite the use of antifouing paint the bottom of the boat is overgrown?

Possible causes

  • Too thin layer of antifouling paint,
  • Choosing the wrong antifouling to type of a boat or yacht
  • Thinning of antifouling paint,
  • Incorrect surface preparation before antifouling application.

How to prevent

  • Apply the right layer thickness of paint indicated by manufacturer,
  • Choose antifouling dedicated to type of boat or yacht and suitable for the type of water,
  • Do not thin antifouling because of the risk of reducing effectiveness,
  • Careful surface preparations (grinding, clearing, degreasing),

How to remove

  • Wet grinding, apply new layers of antifouling paint.
  • Use C1 shell and fouling remover.
Nuestra oferta
Consulte nuestra oferta de materiales y pinturas para la construcción de embarcaciones
Exit
Przewiń na górę