Linguaggio:

THIN FILM SILVER RACING ANTIFOULING

Home » Prodotti » Antivegetativa » THIN FILM SILVER RACING ANTIFOULING
Sea Line farby jachtowe
THIN FILM SILVER RACING ANTIFOULING


Use biocides safely. Always read the label and product information before use.

TypeGRP laminates, wood, steel
PlaceBelow waterline
Function Antifouling paint discourages the growth
of barnacles, weed, and other water life on the submersed hull of the boat.
Application brush, roll

only professional : airless spray gun or conventional spray

Thinning *No recommended
Theoretical coverage For 1lby rollerby spray
11 ~ 12 m²4 ~ 6 m²
Coat thickness (WTF)80 μm160 μm
Finish thickness (DTF)30 μm60 μm
Coats number21
Recommended dry layer60 μm
Hardening the surfaces23ºC15ºC
Touch dry20 minutes30 minutes
Immersion:2 hours3 hours
Dry to recoat (overcoating)min. 6 hoursmin. 10 hours
Dry to launch (immersion times)max 6 monthsmax 6 months
Pack0,75 l2,0 l
Color **codecode
Graphite300008380300008379

* THINNING NOTICE:

In the case of high temperatures and the need to thin the antifouling paint, a maximum dilution of 0-5% (by volume) is recommended.
Dilution and the application method directly affect the thickness of the antifouling paint layer.

Special attention should be paid to obtaining a specific coating thickness (100 μm DTF), which ensures the effective operation of the antifouling paint.

** COLOR NOTICE:

Exposure of a freshly applied antifouling paint to moist air can lead to color change. The discoloration is only superficial and does not affect the effectiveness of the antifouling paint. Due to the content of copper oxide, a small color difference between the parts of the antifouling paint is acceptable.

Antifouling available only in:


Condividi:

Avete domande?
Ti risponderemo il prima possibile
 
Vedi anche
Altri prodotti in questa categoria

Le nostre FAQ
Risposte alle domande più frequenti

Can I paint a boat, previously painted with 1 component paint, with polyurethane?

No, polyurethane is a 2-component paint (base + hardener) and after applying 2-component paint to 1-component paint, the proper adhesion of the paint to the surface will not be maintained, the paint will begin to wrinkle and surface defects will appear.

Why the epoxy filler does not harden?

Possible causes

  • Incorrect proportion of base and herdener,
  • Too low temperature of ambient and surface (less than 10ﹾC),
  • Mixing two components from two different manufacturers,

How to prevent

  • Apply the correct proportions of components
  • Maintain steady temperature (around 20ﹾC) during the whole hardening process,
  • Use base and hardener from the same manufacturer

How to remove

  • The uncured mass requires complete removal from the surface.

Why the paint does not have the right flow?

Possible causes

  • No thinning, wrong thinner or wrong amount of thinner
  • Wrong type of roll or brush (wrong bristle lenght)
  • Applying too much or too Little paint,
  • During painting process temperature was too high or the air was too dry,
  • Incorrect preparation of too porous surface,
  • Incorrect proportion of thinner.

How to prevent

  • Use a brush/Toller suited to the type of surface or paint,
  • Use thinner which is dedicated to the type of application and paints
  • Use thinning proportions which was indicated by manufacturer,
  • Paint in right atmosphere conditions indicated by manufacturer,

How to remove

  • Grind, clean and paint again.
La nostra offerta
Familiarizzate con la nostra offerta di materiali e vernici per la costruzione di barche
Exit
Przewiń na górę