Is elastic sealant recommended for sealing and bonding various types of materials.
POLYMER is recomended for use on :
MS POLYMER
Type | laminat, steel, wood, concret, plexi, etc. |
Place | Above and below waterline |
Function | sealing bonding |
Chemical character | hybrid |
Densinity | 1,44 g/cm³ |
Curing mechanizm | apsorption of moisture from air |
Elogation at break | to 500% (DIN 53 504) |
Tensile strenght | 3,0 N/mm² (DIN 53 504) |
Tear resistance | 20 N/mm |
Resistant to temperatures | -40ºC to + 90ºC |
Resistant to temperatures for short intervals | to +120ºC (white, black) |
to +100ºC (transparent) | |
Time for skin formation 20ºC | 15 minut |
Curing time 20ºC | 24 h (weld to 3 mm) |
Time to contact with water 20ºC | min. 30 minutes |
Time to be painted 20ºC | 3 day |
Shrink | no |
WHITE 200 ml / code : 8208
BLACK 200 ml / code : 8210
TRANSPARENT 200 ml / code : 8211
Apply on surfaces no need to priming.
Steel surfaces is recommend to prime using Epoxy Anticorrosion primer 4:1 Sea-Line.
Wood and concrete is recommend to prime using Epoxy Woodprimer 10:4 Sea-Line.
In case of application on natural wood, its humidity should be lower than 20%.
Clean surfaces from rust, damage paint coatings, etc. To increase adhesion, is recommend to sand surfaces by sand paper :
Clean surfaces from dust and contamination.
Grease and salt remove using Cleaner Sea-Line®
Thanks to advance dispensing system, POLYMER does not require extra tools to application, provides exact thickness of weld during application.
unlock nozzle
unlock dosing regulator
set dosing regulator accordance with the needs
apply product by pressing lever
after finishing application, secure dosing nozzle and block dosing regulator
Cleaner – recommended to degrease the surface before painting. Silicone remover is the product used for surface cleaning before lacquering. […]
DUST MASK DISPOSABLE NITRILE GLOVES “MASTER” DISPOSABLE NITRILE GLOVES WORKWEAR – SINGLE USE POLYESTER WORKWEAR (blue) reusable overall PASTE HAND […]
CORK SANDING BLOCK FOAM SANDING BLOCK PLASTIC SANDING BLOCK PROTECTIVE FOIL PAPER TOWEL (ROLL) ANTISTATIC RAGS CORK SANDING BLOCK Sanding […]
Epoxy filler lightweight 1:1 NEW recommended for large areas due to low own weight PRODUCT DESCRIPTION : low weight and […]
Gelcoat based on IZO/NPG resin, thanks to which it achieves good resistance to weather conditions and high mechanical properties. Primarily […]
GLASS FIBRE MATE Glass fibre mat, in connection with laminating resin, is used for the repairs of big holes in […]
Epoxy Filler Universal “NEW” 2:1 PRODUCT DISCRIPTION : Small repair caused by the action of osmosis. Healed minor damage, small […]
It is not recommended to apply 2K paints over 1K paints. 1K and 2K inks differ in their composition and properties, including hardness, chemical resistance and durability. 1K paints are one-component and dry by evaporating the solvent, while 2K paints are two-component and need to be cured by adding a hardener. Applying 2K paint over 1K paint can cause unpredictable chemical reactions and lead to undesirable effects such as dulling, chipping or flaking of the paint. Therefore, always use paints according to the manufacturer’s instructions and do not mix different types of paints. farby zgodnie z instrukcjami producenta i nie mieszać różnych rodzajów farb.
Refilling and to tackle inequalities caused by damage to or during the course of production
Protects boat surfaces from the effects of destructive activities osmosis and corrosion
Provide an aesthetic and a perfect look of the boat also protective against water and UV radiation
Protect the hull from fouling with algae and shells
Effectively remove scratches, refresh the color of gelcoat or paint, fast shine effect
Special preparations for effective cleaning and refinishing
Laminating, gluing and filling in cracks in gelcoat
Range of products useful in the boat builder work