Γλώσσα:

S0 FAST CUT & MEDIUM GLOSS – στίλβωση πάστα

Ιστοσελίδα » Προϊόντα » Σύστημα στίλβωσης » S0 FAST CUT & MEDIUM GLOSS – στίλβωση πάστα
Farby szkutnicze
S0 FAST CUT & MEDIUM GLOSS – στίλβωση πάστα

S0 στίλβωση πάστα

S0 Brayt είναι μια πάστα στίλβωσης έχει σχεδιαστεί για επαγγελματίες – κατασκευαστές, τα ναυπηγεία και τα προϊόντα όπου σχηματίζει το εξωτερικό στρώμα της τεχνικής gelcoat ή βιομηχανική τελικό επίχρισμα με υψηλή σκληρότητα. S0 αφαιρεί ατέλειες μετά τη λείανση γυαλόχαρτο, ακόμη και P800 (ανάλογα με την σκληρότητα της επιφάνειας). Η πάστα είναι σχεδιασμένη να λειτουργεί με τις μηχανές με μέγιστη ταχύτητα περιστροφής του 1800.

Καλύτερα όταν εφαρμόζεται με μαλλί και σκληρά σφουγγάρια.
Παρέχει μεγάλη στιλπνότητα.


Για την επιφάνειαΤεχνικό gelcoat ή βιομηχανικό τελικό χρώμα με μια υψηλή σκληρότητα.
ΛειτουργίαΑφαιρεί  τις ζημιές, γυαλίζοντας, με λάμψη, προστασία
Τύπος ζημίαςΤρίψιμο με γυαλόχαρτο P800
Εφαρμογήμηχανή
Προτεινόμενη εφαρμογήΑλοιφαδόρος , σκληρός σπόγγος
Συσκευασία1kg         code 11246
ΧρώμαΑσπρο

S0γυάλισμαπάστα-εκπαιδευτικό βίντεο


Μετοχή:

Έχετε ερωτήσεις;
Θα απαντήσουμε το συντομότερο δυνατό
 
Δείτε επίσης
Άλλα προϊόντα αυτής της κατηγορίας

Οι συχνές ερωτήσεις μας
Απαντήσεις σε συνήθεις ερωτήσεις

Why the resin does not harden?

Possible causes

  • Too low temperature of ambitne,
  • Incorrect proportion of base and herdener,
  • Mixing two components from two different manufacturers

How to prevent

  • Apply the correct proportions of components
  • Maintain steady temperature (around 20ﹾC) during whole hardening process,
  • Mix the products thoroughly and bleed the mixture.

How to remove

  • The uncured mass requires complete removal from the surface.

Why the epoxy filler does not harden?

Possible causes

  • Incorrect proportion of base and herdener,
  • Too low temperature of ambient and surface (less than 10ﹾC),
  • Mixing two components from two different manufacturers,

How to prevent

  • Apply the correct proportions of components
  • Maintain steady temperature (around 20ﹾC) during the whole hardening process,
  • Use base and hardener from the same manufacturer

How to remove

  • The uncured mass requires complete removal from the surface.

Why despite the use of antifouing paint the bottom of the boat is overgrown?

Possible causes

  • Too thin layer of antifouling paint,
  • Choosing the wrong antifouling to type of a boat or yacht
  • Thinning of antifouling paint,
  • Incorrect surface preparation before antifouling application.

How to prevent

  • Apply the right layer thickness of paint indicated by manufacturer,
  • Choose antifouling dedicated to type of boat or yacht and suitable for the type of water,
  • Do not thin antifouling because of the risk of reducing effectiveness,
  • Careful surface preparations (grinding, clearing, degreasing),

How to remove

  • Wet grinding, apply new layers of antifouling paint.
  • Use C1 shell and fouling remover.
Η προσφορά μας
Εξοικειωθείτε με την προσφορά μας σε υλικά και χρώματα ναυπήγησης σκαφών
Exit
Przewiń na górę