Γλώσσα:

Polymer

Kosmetyki do naprawy łodzi oraz jachtów
Polymer

Is elastic sealant recommended for sealing and bonding various types of materials.

PRODUCT DESCRIPTION:

POLYMER is recomended for use on :




Characteristic features of POLYMER

BASIC INFORMATION:

MS POLYMER

Type laminat, steel, wood, concret, plexi, etc.
PlaceAbove and below waterline
Functionsealing

bonding

Chemical characterhybrid
Densinity1,44 g/cm³
Curing mechanizmapsorption of moisture from air
Elogation at breakto 500% (DIN 53 504)
Tensile strenght3,0 N/mm² (DIN 53 504)
Tear resistance20 N/mm
Resistant to temperatures-40ºC to + 90ºC
Resistant to temperatures for short intervalsto +120ºC (white, black)
to +100ºC (transparent)
Time for skin formation 20ºC15 minut
Curing time 20ºC24 h (weld to 3 mm)
Time to contact with water 20ºCmin. 30 minutes
Time to be painted 20ºC3 day
Shrinkno

COLOR / PACKAGING / CODE

WHITE 200 ml  /  code : 8208

BLACK 200 ml  /  code : 8210

TRANSPARENT 200 ml  /  code : 8211

SURFACE PREPARATION:

Apply on surfaces no need to priming.

Steel surfaces is recommend to prime using Epoxy Anticorrosion primer 4:1 Sea-Line.

Wood and concrete is recommend to prime using Epoxy Woodprimer 10:4 Sea-Line.
In case of application on natural wood, its humidity should be lower than 20%.

Clean surfaces from rust, damage paint coatings, etc. To increase adhesion, is recommend to sand surfaces by sand paper :

Clean surfaces from dust and contamination.

Grease and salt remove using Cleaner Sea-Line®

APPLICATION:

Thanks to advance dispensing system, POLYMER does not require extra tools to application,  provides exact thickness of weld during application.

MS POLYMER 1

unlock nozzle


MS POLYMER 2

unlock dosing regulator


MS POLYMER 3

set dosing regulator accordance with the needs


MS POLYMER 4

apply product by pressing lever

MS POLYMER 5

after finishing  application, secure dosing nozzle and block dosing regulator


Technical information:


Μετοχή:

Έχετε ερωτήσεις;
Θα απαντήσουμε το συντομότερο δυνατό

Σχετικά προϊόντα

από Polymer


Δείτε επίσης
Άλλα προϊόντα αυτής της κατηγορίας

Οι συχνές ερωτήσεις μας
Απαντήσεις σε συνήθεις ερωτήσεις

Why are the streaks formed?

Possible causes

  • Wrong viscosity and spraying technique,
  • Failure to maintain proper evaporation time and thickness of layers,
  • Incorrect spraying pressure,
  • Too low temperature of varnish, surface or space ,
  • Wrong thinner or hardener.

How to prevent

  • Apply the right type of application method indicated by manufacturer,
  • Use working spray guns,
  • Both the object and material must have room temperature of 20ﹾC,
  • Apply correct proportion of base and hardener.

How to remove

  • Grinding and polishing,
  • Grinding and painting,

Why the epoxy filler does not harden?

Possible causes

  • Incorrect proportion of base and herdener,
  • Too low temperature of ambient and surface (less than 10ﹾC),
  • Mixing two components from two different manufacturers,

How to prevent

  • Apply the correct proportions of components
  • Maintain steady temperature (around 20ﹾC) during the whole hardening process,
  • Use base and hardener from the same manufacturer

How to remove

  • The uncured mass requires complete removal from the surface.

Is it necessary to always sand the surface between application of two different products?

We recommend to always sand the surface between applying two different products to ensure uniform surface roughness and adhesion of subsequent layers. The sanded surface should also be cleaned and degreased.

Η προσφορά μας
Εξοικειωθείτε με την προσφορά μας σε υλικά και χρώματα ναυπήγησης σκαφών
Exit
Przewiń na górę